Workshop Container - Skid 20 Feet

CONTAINER WORKSHOP / LUBRICATION

 

1

External dimensions:

Length= 20 feet= 6058 mm

Width = 8 feet = 2438 mm

Height = 8.6 feet = 2591 mm

Support structure made of cold-drawn steel sheet, two pockets for handling.

Fixed in eight (08) corners.

SKID, connection type: removable

Insulation of all vertical walls and roof with high-density polyurethane panels, 50 mm of thickness for the vertical walls and floor and 70 mm for the roof.

Non-slip steel plate with 2 to 3 mm thickness.

Interior roof coating with smooth aluminum sheets.

Coating from the outside: Steel sheet stamped and galvanized.

Interior wall coatings: melamine resin plywood.

Protective layer: galvanized steel sheet.

Paint color: White (RAL 9010).

The container is divided into 03 compartments by two (02) bulkheads of transverse separation:

Compartment N ° 01: Office, depot for tools and cloakroom

Compartment N ° 02: Machine rooms (generator and compressor)

Compartment N ° 03: Maintenance Station.

8

Electrical installation of the container is 380V / 220 V-50 Hz:

Control panel with safety and control devices.

Lighting installation with LED bar in all three compartments.

A single-phase industrial plug (220V).

Three-phase industrial plug (380V).

A series of power at 220 V in compartment N ° 01 (Office) with three (03) plugs.

Ground connection with plugs and cables.

Electrical Fire-protected cables with special plastic tubes.

Two projectors for exterior lighting.

2

COMPARTMENT N°1: (Office, depot for tools and cloakroom) equipped by:

One (01) wardrobe (dimensions specified by the manufacturer).

One (01) set of complete tools (see list in appendix, from item 01 to 38), IZELTAS brand

One (01) desk with a fixing system

Padded stool with rotating seat and adjustable height.

Three (03) sliding drawers for documents

One (01) washbasin with a mirror, shelf, soap dish, towel hook and electric water heater with 10 liters capacity.

Below the ceiling and between the sink: two (02) plastic potable water tanks (02 tanks of 50 l each) with a filling cap from the outside.

One (01) tank to collect used washbasin water 100 liters capacity on the floor with drainage outside the container

One (01) tropicalized mono block conditioner

One (01) access door from the outside.

A portable microphone (laptop) and inverter

COMPARTMENT N°2 (Machine rooms generator and compressor)

Aeration by moving grids on the two sides of the container

Generator exhaust gas is evacuated out of the container

COMPARTMENT N ° 3 (Tanks/pumps/ Hose reels):

One (01) double door.

One (01) lateral window opening at 90 ° upwards by telescopic pneumatic rod and equipped with a mechanism of safety mechanical locking reserved to the reels for the distribution of different oils and greases.

Recovery system of the used oil towards the tank with capacity of 1000 liters

14

   PUMPS Designation Quantity

Water pump, operated with compressed air

Pressure ratio : (1 : 1)

Max air supply pressure : 08 bars

Min Air pressure : 02 bars

Max water supply pressure : 10 bars

Nominal flowrate : 70 l/min

Completed water pump with hoses and quick coupling (quick coupling for air intake, suction connections and water delivery…), and pressure regulator

01

Oil pump, operated with compressed air

Pressure ratio : (3 : 1)

Max air supply pressure: 08 bars

Min air pressure: 04 bars

Max oil supply pressure: 24 bars

Nominal flowrate : 20 l/min

Hoses set, air and oil connections and pressure regulator for each pump.

08

Oil pump, with pressure regulator

As replacement pumps (replacement of item 02) without connecting hoses

04

Oil piston pump with

Pressure ratio : (1 :1)

Nominal flow : 35 l/min

10 m f hose with pressure regulator rolled on a fixed support and gun.

01

Oil pump, operated with compressed air, for drum 200 L

Pressure ratio : (1 : 1)

Max air pressure : 08 bar

Min air pressure : 02 bar

Flowrate : 70 l/min

Hose connection set, dip tube suitable for 200 liters drum and pressure regulator.

Automatic hose reel for oil with 10 m hose and gun.

01

6

TANKS Designation Quantity
Oil tank

One (01) x parallelepiped tank for used oils

Capacity : 1000 liters

4mm of thickness: steel sheet

Man hole, breather

Hose for pneumatic pump and discharge hose.

01

(08) parallelepiped tanks for new oil :

Capacity: 200 liters.

4mm of thickness: steel sheet

3 '' diameter loading mouth with cap, breather

Hose for pneumatic pump and discharge hose.

08

Water tank

(01) Galvanized tank

Capacity: 500 liters

4mm of thickness : steel sheet.

Features a loading cap, breather and discharge hose.

01

(01) Cooling water tank

Parallelepiped tank

Made of 4 mm thick AISI 304 stainless steel sheet for coolant.

Capacity: 300 liters.

Includes filler tube with cap, breather and discharge hose.

01
Fuel tank

(01) parallelepiped fuel tank

Capacity:100 liters

4mm of thickness: sheet steel.

Includes loading hose, breather and discharge hose.

01

7

HOSE REELS Designation Quantity

Hose reels with automatic oil system

Length = 15 m of hose.

Dispensing gun with digital counter max flow 35 l / min with flexible end and semi-automatic anti-drip nozzle

08

Hose reels with automatic grease system

Length = 15 m of hose

High pressure grease gun and accessories

04

One (01) hose reel with automatic water system

Length = 15 m of hose.

Low Pressure Distribution Gun.

01

One (01) hose reel with automatic system for compressed air

Length = 15 m of hose for compressed air with:

- A blowgun with aluminum spray nozzle.

- A tire inflation gun with pressure gauge.

01
       

3

TOOL LIST

Item Designation Quantity
01 Mixed wrenches 13-14-17-19-21 to 25-32 01
02 Adjustable wrenches 8’’ and 10’’ 01
03 Ratchet ½ "extension ½": 250 mm 01
04 Sockets ½ '' 13-17-22-24-30-32-34 mm 01
05 Screwdriver for slotted screws 3.5x100, 5.5x100mm 01
06 Slotted screwdriver 6.5x 100, 8x 200 mm 01
07 Screwdriver Pozidriv PZ 1 to 4 01
08 Screwdriver Torx N° 20, 25 et 27 01
09 T-handle screwdriver 01
10 Crank wrench 8, 10 and 17 01
11 Torx wrenches T8, T10, et T15 01
12 Locking pliers 01
13 Coated universal clamp 01
14 Clamp 01
15 32 mm riveting hammer 01
16 Burin 01
17 Burette 01
18 Magnetic finger 01
19 Sockets for spark plugs of 14 mm 3/8 '' - 90 and 250 mm 01
20 Sockets for spark plugs of 16 mm 3/8 '' - 90 and 250 mm 01
21 Articulated wrenches for 16 mm-short and long candles 01
22 Articulated wrenches for 21 mm-short and long candles 01
23 Spark plug wrenches 01
24 Ratchet (palm of hand) 01
25 Candle support 01
26 Composition draining: magnetic key and tip 01
27 Extension 01
28 3/8 '' universal joint 01
29 Long articulated ratchet 01
30 Wrench for self-tightening oil filter 01
31 Automatic oil filter wrench 01
32 Oil filter wrench Ø 76 mm 01
33 Oil filter wrench Ø 86 mm 01
34 Oil filter wrench Ø 96 mm 01
35 Thickness gauge 19 blades 01
36 Lime tool 01
37 effort Lever 01
38 Cross wrench 01